Boot Block Recovery For Free
کد:
Boot Block Recovery For Free
You don't need to pay a measly sum of dollars just to recover from a boot block mode. Here it is folks:
AWARD Bootblock recovery:
That shorting trick should work if the boot block code is not corrupted, and it should not be if /sb switch is used when flashing the bios (instead of /wb switch).
The 2 pins to short to force a checksum error varies from chip to chip. But these are usually the highest-numbered address pins (A10 and above).
These are the pins used by the system to read the System BIOS (original.bin for award v6), calculate the ROM checksum and see if it's valid before decompressing it into memory, and subsequently allow Bootblock POST to pass control over to the System BIOS.
You just have to fool the system into believing that the System BIOS is corrupt. This you do by giving your system a hard time reading the System BIOS by shorting the 2 high address pins. And when it could not read the System BIOS properly, ROM Checksum Error is detected "so to speak" and Bootblock recovery is activated.
Sometimes, any combination of the high address pins won't work to force a checksum error in some chips, like my Winbond W49F002U. But shorting the #WE pin with the highest-numbered address pin (A17) worked for this chip. You just have to be experimentative if you're not comfortable with "hot flashing" or "replacement BIOS".
But to avoid further damage to your chip if you're not sure which are the correct pins to short, measure the potential between the 2 pins by a voltmeter while the system is on. If the voltage reading is zero (or no potential at all), it is safe to short these pins.
But do not short the pins while the system is on. Instead, power down then do the short, then power up while still shorting. And as soon as you hear 3 beeps (1 long, 2 short), remove the short at once so that automatic reflashing from Drive A can proceed without errors (assuming you had autoexec.bat in it).
About how to do the shorting, the tip of a screwdriver would do. But with such minute pins on the PLCC chip, I'm pretty comfortable doing it with the tip of my multi-tester or voltmeter probe. Short the pins at the point where they come out of the chip.
AMIBIOS Recovery bootblock:
1. Copy a known working BIOS image for your board to a floppy and rename it to AMIBOOT.ROM.
2. Insert the floppy in your system's floppydrive.
3. Power on the system while holding CTRL+Home keys. Release the keys when you hear a beep and/or see the floppy light coming on.
4 . Just wait until you hear 4 beeps. When 4 beeps are heard the reprogramming of the System Block BIOS went succesfull, so then you may restart your system.
Some alternative keys that can be used to force BIOS update (only the System Block will be updated so it's quite safe):
CTRL+Home= restore missing code into system block and clear CMOS when programming went ok.
CTRL+Page Up= restore missing code into system block and clear CMOS or DMI when programming went ok.
CTRL+Page Down= restore missing code into system block and do not clear CMOS and DMI area when programming went ok
Btw: the alternative keys work only with AMIBIOS 7 or higher (so for example an AMI 6.26 BIOS can be only recovered by using CTRL+Home keys).
Boot Block Recovery for FREE
************************************************
BLACKOUT Flashing
*************************************************
Recovering a Corrupt AMI BIOS chip
With motherboards that use BOOT BLOCK BIOS it is possible to recover a corrupted BIOS because the BOOT BLOCK section of the BIOS, which is responsible for booting the computer remains unmodified. When an AMI BIOS becomes corrupt the system will appear to start, but nothing will appear on the screen, the floppy drive light will come on and the system will access the floppy drive repeatedly. If your motherboard has an ISA slot and you have an old ISA video card lying around, put the ISA video card in your system and connect the monitor. The BOOT BLOCK section of the BIOS only supports ISA video cards, so if you do not have an ISA video card or your motherboard does not have ISA slots, you will have to restore your BIOS blind, with no monitor to show you what’s going on.
AMI has integrated a recovery routine into the BOOT BLOCK of the BIOS, which in the event the BIOS becomes corrupt can be used to restore the BIOS to a working state. The routine is called when the SYSTEM BLOCK of the BIOS is empty. The restore routine will access the floppy drive looking for a BIOS file names AMIBOOT.ROM, this is why the floppy drive light comes on and the drive spins. If the file is found it is loaded into the SYSTEM BLOCK of the BIOS to replace the missing information. To restore your BIOS simply copy a working BIOS file to a floppy diskette and rename it AMIBOOT.ROM, then insert it into the computer while the power is on. The diskette does not need to be bootable or contain a flash utility. After about four minutes the system will beep four times. Remove the floppy diskette from the drive and reboot the computer. The BIOS should now be restored.
Recovering a Corrupt AWARD BIOS
With AWARD BIOS the process is similar but still a bit different. To recover an AWARD BIOS you will need to create a floppy diskette with a working BIOS file in .BIN format, an AWARD flash utility and an AUTOEXEC.BAT file. AWARD BIOS will not automatically restore the BIOS information to the SYSTEM BLOCK for this reason you will need to add the commands necessary to flash the BIOS in the AUTOEXEC.BAT file. The system will run the AUTOEXE.BAT file, which will in turn flash the BIOS. This is fairly easy. Here are the steps you need to take.
· Create a bootable floppy diskette
· Copy the BIOS file and flash utility to the diskette
· Create an text file with any standard text editor and add the following lines
@ECHO OFF
FLASH763 BIOSFILE.BIN /py
In the above example I am assuming that you are using the FLASH763.EXE flash utility. You will need to replace the FLASH763 with the name of whatever flash utility you are using, and replace the BIOSFILE.BIN with the name of the BIOS file you are using. You will also need to change the ‘/py’ to whatever the command is for your flash utility to automatically program the BIOS without user intervention. If you do not know the command to automatically flash your BIOS type the name of the flash utility with a space and then /? to display the utility’s help screen. The help screen should pecify the command switch to automatically flash your BIOS. If you are using the FLASH763.EXE utility then the switch to automatically flash your BIOS is ‘/py’.
Border And Text Effects In Psp8, For use with PSP8
کد:
Do you want to jazz up your graphics? Want to add a bit of pazazz to your art? Well, this guide features some knowledge, border effects, and even directions to make your own swirlie brushes!
Now, open PSP and get ready to learn! Let's start off with the basics.
-------------------------------------------------
-Border Effects
There are two main types of borders, solid borders, and decorative borders. A solid border is like a colored line that raps around the outside of your image and separates graphics from the rest of the page. You can have borders inside the outside borders to make awesome layer effects. Decorative borders are almost the same, except they are not completely connected. (Example - Dashed Borders)
-------------------------------------------------
Dashed Borders
Open PSP and create an image about 380 x 100 pixels with a white background.
Draw a bit with your paintbrush, just add some color. Now maximize your image.
It should take up the whole page. Now go up to the toolbar on the very top and click "Selections" and go down right below that and click "Select All" There should be a dotted line going around the outside of your image.
We're almost done! YAY! Ok, now look on your keyboard. Go to the very top row next to the F1, F2, F3, F4, and look to the right of the F12 button. It should say "Print Screen". Press it, and it will take a picture of everything currently open on your computer that you can see. Now go to the top toolbar once one. Go under "Edit", move down to "Paste", then move your mouse to the right and select "Paste as New Image"
Now, your image has a dashed border, but you can see all the unwanted parts of your workspace. So go to the left toolbar and click the crop tool. It is the small square with a line through it.
Now drag the segment the crop tool makes just around the image. You might want to zoom in some (Click the magnifying glass on the left toolbar on the spot you want to zoom in). Once you have it fully outlined with the crop segment, double-click to crop it. Wallah! Your image now has a dashed border. So just go to the top toolbar once again, go under "File" and click "Save As". Then, select the spot and name to save it.
-------------------------------------------------
-Font Suggestions and Styles
So you know how to make a cool border for your images. Now what about fonts? Well usually, for siggies, you would put a bigger font saying their name, and a smaller font with sub-text. Look at my signature:
See how it says "Anonymous" in a large font that matches the background; then under it, it says "SOD's coolest member" (my sub-text) in a smaller font? That's the usual format for text on signatures. Of couse, this isn't the only way.
Now, for some font suggestions:
Larger Fonts
Laurenscript
Baby Kruffy (This one is awesome!)
Casual
Chick
Cheri
Walt Disney
Mullet
Dolphins (yippee!)
Jelly Belly
Flubber
Porky's
Gilligan's Island
Cheeseburger
Smaller Fonts
Redensek
Mullet
Georgia
Acknowledge
Tahoma
-------------------------------------------------
Helpful Links
http://peachie.nu
(a few popups though)
Font Places
http://www.dafont.com/en/
http://www.1001freefonts.com/
http://www.fontfreak.com/
http://www.acidfonts.com/
Bulk Editing Of .xxx to .zip or .mp3
کد:
lets us say you have just download a new album or game
but all the files are .xxx and you need them to be
zip's, rar's, mp3's etc.....
then do the following
-create a new folder
-put all the files needing editing in the new folder
-then goto "run" in the start menu
-type in CMD and click ok
-the next thing needsa few bits of old dos commands
-you need to navagate CMD to the folder whree the files are
-you can do this by 1st getting the total adress of the folder
-and then typing it in cmd with a "cd" in frount
QUOTE
cd c:\xxx\yyy\ccc\
once you in the folder where the files are you can move on
nb u can cheek you in the right folder by typing dir to get a list of files
-now type in....
QUOTE
rename *.* *.zip
Nb change the zip to what ever the extention needs to be (.rar, .mp3 ect)
all done
you should hv now changed the .* to what ever you needed
happy downloading Benji
(by Benji)
nb to exit CMD type in "exit"
BulletProof FTP Server Tutoria
کد:
thanks to someone for this tut.
Configuring your Bulletproof FTP Server Tutorial
I am not sure where I found this tutorial, It’s been a while…It might even have been here... ..So if it is one of yours, my hat goes off to you once again....
After reading the excellent tutorial on "Creating an FTP" that Norway posted…
(I would suggest reading and following his tutorial first, then following up with this one)
I thought that perhaps this tutorial might be pretty helpful for those interested in knowing how to configure their Bulletproof FTP Server that don't already know how... Here's how to get started…
This is for the BulletProof FTP Server 2.10. However, It should work fine on most following versions as well.
I'm assuming you have it installed and cracked.
Basics
1. Start the program.
2. Click on Setup > Main > General from the pull-down menu.
3. Enter your server name into the 'Server Name' box. Under Connection set the “Max number of users" to any number. This is the limit as to how many users can be on your sever at any time.
4. Click on the 'options' tab of that same panel (on the side)
5. Look at the bottom, under IP Options. Put a check in the box “Refuse Multiple Connections from the same IP”. This will prevent one person from blocking your FTP to others.
6. Also put a check in the 'Blocked Banned IP (instead of notifying client). VERY IMPORTANT! If somebody decides to 'Hammer' (attempt to login numerous times VERY quickly) your server/computer may CRASH if you don't enable this.
7. Click on the 'advanced' tab
8. At the bottom again look at the 'hammering area'
9. Enable 'anti-hammer' and 'do not reply to people hammering' Set it for the following: Block IP 120 min if 5 connections in 60 sec. You can set this at whatever you want to but that is pretty much a standard Click 'OK'
Adding Users
11. Setup > User accounts form pull-down.
12. Right click in the empty 'User Accounts' area on the right: choose 'Add'
13. Enter account name. (ie: logon name)
14. In the 'Access rights' box right click: choose ‘Add’.
15. Browse until you find the directory (folder) you want to share. In the right column you will see a bunch of checkboxes. Put a check in the following ones: Read, Write, Append, Make, List, and +Subdirs. Press 'select'.
16. Enter a password for your new FTP account.
17. Click on 'Miscellaneous' in the left column. Make sure 'Enable Account' is selected. Enable 'Max Number of Users' set it at a number other than zero. 1 for a personal account and more that one for a group account. Enable 'Max. no. of connects per IP' set it at 1
18. Under 'Files' enable 'show relative path' this is a security issue. A FTP client will now not be able to see the ENTIRE path of the FTP. It will only see the path from the main directory. Hide hidden flies as well.
Put a tick in both of these.
Advanced:
You don't need to do any of this stuff, but It will help tweak your server and help you maintain order on it. All of the following will be broken down into small little areas that will tell you how to do one thing at a time.
Changing the Port
The default port is always 21, but you can change this. Many ISPs will routinely do a scan of its own users to find a ftp server, also when people scan for pubs they may scan your IP, thus finding your ftp server. If you do decide to change it many suggest that you make the port over 10,000.
1. Setup > Main > General
2. In the 'Connection' Area is a setting labeled 'Listen on Port Number:'
3. Make it any number you want. That will be your port number.
4. Click 'OK'
Making an 'Upload Only' or 'Download Only' ftp server.
This is for the entire SERVER, not just a user.
1. Setup > Main > Advanced
2. In the advanced window you will have the following options: uploads and downloads, downloads only, and uploads only. By default upload and download will be checked. Change it to whatever you want.
3. Click 'OK’
While you are running your server, usually you will end up spending more time at your computer than you normally do. Don't be afraid to ban IP's. Remember, on your FTP you do as you want.
When you are online you must also select the open server button next to the on-line button which is the on-line Button
You also have to use the actual Numbered ip Address ie: 66.250.216.67
Or even Better yet, get a no-ip.com address
Burn .bin file Without A .cue file
کد:
To burn a bin file, you will need an appropriate cue file.
You do exactly the same as for iso files, but when you click on “burn image,” you don’t browse to the bin itself, but instead to the cue file, and you open that one.
When the writer starts to burn, it will automatically search for the bin file and start burning it. In fact, the cue file tells the burning program where it can find the bin file that is attached to it. It is VERY IMPORTANT that you use the right cue file when you burn a bin. i.e both cue and bin files that are attached to each other must be located in the same folder, and every bin file has it’s own cue file.
Normally, when you download a bin file, you can download the appropriate cue file as well. If you do not have the cue file (or feel bold) you can make the cue file yourself, which is really easy to do:
a. Open notepad
b. Copy the folowing text into notepad:
FILE“nameofimage“BINARY
TRACK 01 MODE1/2352
INDEX 01 00:00:00
Where nameofimage.bin is the name of the bin file you want ot burn.
c. The rest is easy: just save the notepad text with the name of the bin, but with the cue extension.
d. The file should be saved in the same folder as its appropriate bin file and should be something like myfile.cue
Or you can use Alcohol 120% to burn directly from the bin file
Burn a BIN without a CUE using NERO
کد:
Burn a BIN without a CUE using NERO
You've downloaded a *.BIN file, but there was no *.CUE file associated and you still want to burn the *.BIN file using Nero
Your options are:
1) Create yourself a *.CUE
2) Convert the *.BIN to an *.ISO
3) OR use Nero to burn without the *.CUE file!!!
Yes, that's possible... just follow these steps and you will be sorted. No need for *.CUE files anymore
Ok, here we go...
1) Start Nero
2) File -> Burn Image
3) Browse to the *.BIN file that you want to burn and open it
4) A window saying "Foreign Image Settings" will open
5) Check the settings. They should be as followed:
* Type of image: leave it to Data Mode 1
* Select the Raw Data check box
Note ->> The block size will change automatically from 2048 to 2352
* Leave Image Header and Image Trailer unchanged and set to 0
* Leave "Scrambled" and "Swapped" check boxes unchecked
6) Click on burn!
7) Enjoy
This tut was for Nero 5.x.x.x, I was told that "Burn Image" is under "recorder" in Nero 6. The rest of the steps should be the same...
xkalibur
