دقيقا مدل هاردت رو مينويسي ؟
Printable View
دقيقا مدل هاردت رو مينويسي ؟
سلام ... سپاس از همه ی دوستان که تجربیاتشون رو در اختیار من قرار دادند . مدل هارد دیسک Maxtor DiamondMax Plus 9 هست . چون عکسش رو یکی از دوستان توی همین تاپیک گذاشته من دیگه نمی گذارم . اما اگه این مدل انواع متفاوتی داره بگید که هم عکس بگذارم و هم مشخصات ریزتر ...
با نرم افزار seatools هم تست می کنم و جواب می دم...
در ضمن توی یه فروم انگلیسی هم دیدم که یه نفر همین مشکل من رو داشت و جالب ابنکه حجمی که نشون می ده دقیقا 33280 بود .. این هم لینک اون تاپیک انگلیسی ...
برای مشاهده این لینک/عکس می بایست عضو شوید !برای عضویت اینجا کلیک کنید ]
من موردی که گفتم رو تست کردم دیروز باید جواب بده :give_rose:نقل قول:
2 GB - 33.8 GB Limitation32 GB - 33.8 GB Limitation
div.inner_center_main_content ol li p {font-size:100%;}If the operating system, BIOS, DiscWizard, or MaxBlast can only recognize 32 GB of the drive it may be caused by one of the following:
Drive Jumpers: Applies to Mac and Windows users. On ATA/IDE drives that are larger than 32 GB there is a Capacity Limitation Jumper (CLJ), also known as the Limit Capacity Jumper or the Alternate Capacity (AC) Jumper setting. This jumper will limit the capacity of the drive to 32 GB and should only be used when the BIOS hangs when trying to auto-detect the drive. If you have two jumper shunts on the drive you will need to remove the CLJ or AC jumper. For more information on Seagate and Maxtor ATA jumper settings, see برای مشاهده این لینک/عکس می بایست عضو شوید !برای عضویت اینجا کلیک کنید ]
If you format the drive with the CLJ or AC jumper then the drive capacity will be limited to 32GB. After removing the CLJ or AC jumper the drive will still be recognized as 32GB. You must reformat the drive without the CLJ or AC jumper to gain the full capacity of the drive, which will erase all the data on the drive. The other option is to create a second partition with the remaining unallocated disc space. See برای مشاهده این لینک/عکس می بایست عضو شوید !برای عضویت اینجا کلیک کنید ] on reformatting a hard drive.
- BIOS: On older systems (pre- November 1998) the BIOS may not support drives that are larger than 32 GB. In the BIOS setup please set the drive type to AUTO detect. If the BIOS detects the full capacity of the drive then the BIOS will support the capacity of the drive. If not please perform one of the following:
- Check with the system or motherboard manufacturer for any BIOS upgrades for the system.
- If a BIOS update is not available from the manufacturer you can also visit the following site: برای مشاهده این لینک/عکس می بایست عضو شوید !برای عضویت اینجا کلیک کنید ] and download the BIOS Agent to determine if an update is available for purchase for your system. The BIOS Agent will identify the BIOS on your system and provide you with all of the information that you will need for ordering a BIOS update. Seagate provides this information as a courtesy to its customers and has no official affiliation with esupport.com.
- (Recommended) Purchase a PCI ATA controller card that will support the capacity of the drive. The two benefits of ATA controller cards are:
- The ability to support large capacity drives
- The ability to support the faster transfer rates of the drive.
- Operating System: Windows Vista/XP/2000 have a 32 GB format limitation for FAT 32. That means if you formatted the drive in FAT 32 with Windows Vista/XP/2000, the largest partition supported is 32 GB. You will need to format the drive in NTFS if you want to partition the drive larger than 32 GB.
Another option is to create (an) additional partition(s) with the remaining unallocated disc space.
A third option is to format the drive using DiscWizard, MaxBlast, or FDISK in Windows 98 or ME.
Incorrect Reporting to the BIOS: The drive itself may be reporting the incorrect size to the BIOS. In order to correct this, you will need to download برای مشاهده این لینک/عکس می بایست عضو شوید !برای عضویت اینجا کلیک کنید ], boot into the SeaTools disc, and run the Set Capacity utility.
NOTE: It is recommended that you only have the hard drive reporting the incorrect capacity connected to your system while performing the following steps. Any other hard drives should be disconnected.
NOTE: It is recommended that you back up any important data on the hard drive before using SeaTools to set the drive size. This is a potentially data destructive procedure. Seagate is not responsible for any lost data.
See برای مشاهده این لینک/عکس می بایست عضو شوید !برای عضویت اینجا کلیک کنید ] for a tutorial on Seatools for DOS. Also see below:
- Insert the SeaTools for DOS CD or floppy disc into the appropriate drive, and restart your computer. When SeaTools boots up, carefully read the license agreement, and press Y if you accept it.
- Select the correct drive from the list at the bottom of the screen, by pressing its corresponding number on your keyboard.
- Press C to select the Set Capacity option.
- Press M to reset the drive to its maximum capacity.
- Once the capacity has been set, SeaTools has returned to the main screen, take the SeaTools CD out of the drive and completely power down the system. The system needs to be shut down so any cached information is cleared. If you simply reboot or reset your computer without completely powering it down first, the corrected capacity setting will not take effect.
After correcting the drive capacity, the drive will still be recognized as 32GB. You must reformat the drive to gain the full capacity of the drive, which will erase all the data on the drive. The other option is to create a second partition with the remaining unallocated disc space.
Jumper Settings
Below are the different jumper setting configurations you may encounter using the Limit Capacity Jumper Setting on Seagate drives:
(And see برای مشاهده این لینک/عکس می بایست عضو شوید !برای عضویت اینجا کلیک کنید ] for Maxtor drives.)
Single Master with Limit Capacity
[ :] : : [:]
Slave with Limit Capacity
: : : [:]
Master with Non-ATA Compatible Slave
This is usually ATAPI devices like CD-ROMs plus Limit Capacity
برای مشاهده این لینک/عکس می بایست عضو شوید !برای عضویت اینجا کلیک کنید ]
برای مشاهده این لینک/عکس می بایست عضو شوید !برای عضویت اینجا کلیک کنید ]
من اون نسخه از نرم افزار sea tools را دارم که توی hiren هست . ولی توی اون نرم افزار advanced نداشت .نقل قول:
من اون نسخه از نرم افزار sea tools را دارم که توی hiren هست . ولی توی اون نرم افزار advanced نداشت .نقل قول:
اگه لینکش رو داری بگذار ...
این لینک فایل ایمیجش هست که باید روی سی دی رایت کنید
کد:http://www.seagate.com/staticfiles/support/seatools/SeaToolsDOS213bEURO.ISO
راستی کسی می دونه این LBA و CHS که توی ست آپ نوشته چی هستند و مفهومشون چیه؟
سلام
برای رفع این مشکل از نرافزار mhdd باید استفاده کنی.بر روی گزینه restor to factory size برو و کار تمومه...
(در حین کار با نرم افزار میتونی از help اون استفاده کنی.توسط کلیدF1)
نقل قول:
توی hiren بود . اما گزینه ای که تو گفتی نداشت . اگه می شه عین دستوری رو که باید بنویسم برام بگذار ... ممنون
راستی یه سوال ... چی شده که این هارد اینطوری شده ؟ و چی می شه که با این نرم افزار به تنظیمات کارخانه بر می گرده ؟